Energy StoragePower Grids

BESS Black Start with Grid-Forming Inverters: Sequence, Energy Budget and Testing

Black start is the ability to energise a dead electrical system without relying on an external grid. A battery energy storage system with grid-forming controls can establish voltage and frequency quickly, but successful restoration requires more than stored MWh. The inverter must energise transformers, tolerate load steps, supply reactive current and coordinate protection while the island has very low fault strength.

Core principle: black-start capability is determined by transient current, control stability, auxiliaries and sequence as much as by battery energy. A BESS with ample MWh can still fail to energise one transformer.

Grid-following versus grid-forming

A grid-following inverter measures an existing voltage waveform and injects current relative to it. It normally cannot energise a completely dead bus by itself. A grid-forming inverter establishes a voltage magnitude and frequency reference and responds to load changes within its current and energy limits.

Grid-forming control may use droop, virtual synchronous machine or other vendor-specific methods. The project needs validated models and a defined transition between islanded and grid-connected modes.

What a black-start BESS must do

  • Start its own controls, cooling and fire-safety auxiliaries.
  • Close onto a dead bus safely.
  • Establish stable voltage and frequency.
  • Energise cables, transformers and reactors.
  • Pick up station-service and process loads in steps.
  • Start selected motors.
  • Maintain SoC and thermal margin.
  • Coordinate with protection in a weak island.
  • Synchronise restored islands or reconnect to the grid.

Start with station auxiliaries

The BESS may need DC controls, HVAC, pumps, communication, switchgear and fire systems before its power conversion system can operate. Provide an independent source such as:

  • Battery-backed control DC.
  • UPS.
  • Small diesel generator.
  • Dedicated low-voltage black-start battery.
  • Self-start converter path from the main battery.

Map every dependency. A grid-forming PCS cannot start if its cooling pump depends on the dead AC bus it is meant to energise.

Energy budget example

Assume a 20 MW / 40 MWh BESS begins at 80% SoC. The restoration plan reserves operation down to 20% SoC.

Usable black-start energy:

Eusable = 40 × (0.80 − 0.20) = 24 MWh

Assume:

  • BESS and substation auxiliaries: 1 MW.
  • Initial restored loads: 5 MW for 2 hours.
  • Conversion and distribution allowance: 8%.

Required energy before losses:

Eload = (1 + 5) × 2 = 12 MWh

Including 8% allowance:

Erequired ≈ 12 / 0.92 = 13.0 MWh

The 24 MWh usable reserve passes the energy screen, leaving margin for delays. This does not prove transformer energisation or motor-start capability.

Power and current limits

At 20 MW rating, a 5 MW initial load is modest in active power. However, transformer inrush can demand several per-unit current for a short period. The inverter current limiter may clamp output, causing voltage collapse or a failed energisation attempt.

Request vendor data for:

  • Peak current magnitude and duration.
  • Reactive-current priority.
  • Negative-sequence current capability.
  • Current-limiter recovery.
  • DC-link and battery current limits.
  • Repeated energisation attempts.

Transformer energisation

Inrush depends on closing angle, residual flux, core design, source impedance and voltage. A stiff grid can supply high inrush; an inverter-limited source behaves differently. Study:

  • Uncontrolled closing.
  • Point-on-wave controlled closing.
  • Pre-insertion resistor or reactor.
  • Reduced-voltage energisation followed by ramp-up.
  • Energising from HV or LV side.
  • Sequential phase closing where equipment permits.

The inverter control model must be valid during current limiting and distorted flux conditions.

Controlled voltage ramp

A grid-forming inverter may energise a transformer by closing at low voltage and ramping magnitude slowly. This can reduce inrush but requires coordination with transformer protection, auxiliary supplies and equipment undervoltage limits. Confirm the vendor supports the mode and that voltage-dependent loads remain disconnected.

Cable and reactor charging

Long cables generate capacitive current. Energising a cable, transformer and shunt reactor together can produce resonant transients. The sequence should be validated using electromagnetic-transient simulation, especially for offshore wind or remote renewable grids.

Motor starting in an island

Motor starting draws high current and reactive power. A 500 kW motor with 5.5-times starting current can exceed inverter current even when the BESS has 20 MW active-power capacity. Options include:

  • VFD starting.
  • Soft starter.
  • Starting before other loads.
  • Smaller motors in sequence.
  • Temporary load shedding.
  • Reduced mechanical load.

Check torque and acceleration time, not only current reduction.

Island frequency control

The BESS initially balances every mismatch between generation and load. Droop control can share power when a diesel generator, hydro unit or another BESS joins. Define:

  • Frequency setpoint and droop.
  • Active-power reserve.
  • Rate limits.
  • Underfrequency load shedding.
  • Overfrequency response after load rejection.
  • Secondary control that restores nominal frequency.

Voltage and reactive-power control

The inverter must supply cable charging, transformer magnetising current and load kvar. Define:

  • Voltage setpoint and Q-V droop.
  • Current priority during voltage events.
  • Shunt reactor and capacitor switching.
  • Tap-changer blocking or control in island mode.
  • Reactive limits at current SoC and temperature.
  • Secondary voltage control after more sources connect.

Protection in a weak island

Inverter fault current may be limited to 1.1–2.0 pu and controlled in phase. Traditional instantaneous overcurrent protection can lose sensitivity. Review:

  • Differential protection.
  • Directional and voltage-restrained elements.
  • Negative-sequence protection.
  • Distance protection performance.
  • Breaker-failure logic.
  • Earth-fault current and grounding source.
  • Protection-setting groups for island and grid modes.

Do not assume utility-grid fault levels during black start.

Grounding the island

The restored network needs a defined neutral reference. The grounding source may be a transformer neutral, grounding transformer or generator. Ensure it is connected before energising loads that require earth-fault protection. Avoid parallel grounding points after islands are synchronized.

Load restoration priority

A representative sequence is:

  1. BESS internal auxiliaries.
  2. Substation DC, protection and communications.
  3. One station-service transformer.
  4. Essential HVAC, pumps and lighting.
  5. Critical process loads.
  6. A dispatchable generator’s auxiliaries.
  7. Generator start and synchronisation.
  8. Additional feeder blocks.
  9. Noncritical loads.

Each step should wait for voltage, frequency and thermal recovery.

Cold-load pickup

After a long outage, thermostatic loads, motor compressors and transformer magnetising demand can return simultaneously. Aggregate demand may exceed pre-outage load. Use staged feeder pickup, controlled HVAC restart and load shedding.

Bringing conventional generation online

A black-start BESS can energise auxiliaries for a gas turbine, diesel, hydro or thermal unit. Once the generator is stable:

  • Synchronise it to the BESS island.
  • Transfer active and reactive load gradually.
  • Coordinate droop and governor response.
  • Maintain BESS headroom for disturbances.
  • Decide which device remains grid-forming.

Poorly coordinated controls can oscillate or fight over frequency and voltage.

Synchronising islands

Before closing a tie breaker, verify voltage magnitude, frequency, phase angle and phase sequence. Synch-check settings need suitable windows for a low-inertia island. Communications-assisted synchronisation may adjust one island’s frequency to close the angle gradually.

SoC management

Reserve enough energy for:

  • Expected restoration duration.
  • Failed energisation attempts.
  • Auxiliary load.
  • Weather-dependent HVAC.
  • Delayed generator start.
  • Post-restoration contingency.

Set a minimum SoC at which noncritical restoration stops and a controlled fallback begins.

Thermal constraints

Grid-forming operation can require sustained reactive current and repeated transients. Monitor battery temperature, inverter semiconductor temperature and cooling redundancy. MWh reserve does not override current or thermal limits.

Communication failure

The core grid-forming function should remain safe if the central controller or WAN link fails. Define local fallback for:

  • Voltage and frequency reference.
  • Maximum load pickup.
  • SoC floor.
  • Protection setting group.
  • Generator droop.
  • Load shedding.

Modelling workflow

Use several study types:

  • RMS dynamic simulation for load steps and governor interaction.
  • Electromagnetic-transient simulation for transformer and cable energisation.
  • Harmonic and resonance analysis.
  • Protection study with inverter fault-current models.
  • Energy/SoC simulation for restoration duration.

Validate models against factory tests or staged site tests.

Commissioning stages

  1. Test auxiliaries and self-start without energising the grid.
  2. Energise a small dead bus.
  3. Verify voltage and frequency control.
  4. Energise transformer using the approved method.
  5. Add resistive or load-bank steps.
  6. Start the largest permitted motor.
  7. Test load rejection.
  8. Synchronise a second source.
  9. Verify protection setting changes.
  10. Conduct a full restoration drill under controlled conditions.

Record high-speed voltage, current, frequency, power, SoC and controller states.

Common mistakes

  • Checking MWh but not inverter peak current.
  • Forgetting that BESS cooling depends on station AC.
  • Using a stiff-grid transformer model for inverter energisation.
  • Applying utility protection settings in a weak island.
  • Ignoring neutral grounding before load pickup.
  • Starting large motors after other loads are restored.
  • Assuming communications are always available.
  • Using one successful factory test as proof for the complete network.

Frequently asked questions

Can any BESS perform black start?

No. It needs self-starting auxiliaries, suitable grid-forming controls, switching logic, current capability and validated protection.

Does grid-forming mean unlimited fault current?

No. Power-electronic devices remain current-limited. Protection must be designed for their controlled fault response.

How much SoC should be reserved?

It depends on restoration time, auxiliaries, load sequence, failed attempts and the next source to start. Use an energy model and operational margin.

Conclusion

BESS black start is a coordinated restoration function, not a simple inverter setting. Prove self-starting auxiliaries, transformer energisation, motor starting, island protection, SoC reserve and synchronisation. Staged testing with validated grid-forming models turns stored battery energy into a dependable restoration resource.

This article is educational engineering guidance. Black-start design and testing require utility approval, manufacturer models and controlled operating procedures.

Featured photo by Manuel on Unsplash.

Related Articles