Electrical CircuitsEngineering Applications

Three-Phase Power Calculation: kW, kVA, Current and Power Factor

Quick answer: For a balanced three-phase load using line-to-line voltage, apparent power is S = √3 × VLL × I, and active power is P = √3 × VLL × I × PF. Use volts and amperes for VA, then divide by 1,000 for kVA or kW. The formula does not replace phase-by-phase analysis for materially unbalanced loads.

Electrical experiment equipment used for three-phase power calculations
Photo by Nicolas Thomas under the Unsplash License.

Define the quantities first

  • VLL: RMS line-to-line voltage.
  • I: RMS line current for the balanced load.
  • S: apparent power in VA or kVA.
  • P: active power in W or kW.
  • Q: reactive power in var or kvar.
  • PF: total power factor, P/S.

Do not mix a line-to-neutral voltage with the √3 line-to-line formula. For a balanced wye system, VLL = √3 VLN; the total power is also three times the per-phase power.

Core balanced-load equations

S = √3 VLLI

P = √3 VLLI PF

Q = √(S² − P²) for the magnitude when P and S are known.

Rearranging gives I = P /(√3 VLL PF η) when P is useful mechanical output and motor efficiency η must be included. If P is measured electrical input, do not divide by efficiency again.

Worked example: 400 V distribution load

A balanced load draws 80 A from a 400 V three-phase supply at power factor 0.85.

  1. S = 1.732 × 400 × 80 = 55,424 VA ≈ 55.4 kVA.
  2. P = 55.4 × 0.85 = 47.1 kW.
  3. Q = √(55.4² − 47.1²) ≈ 29.2 kvar.

A quick check is P < S when PF < 1. If the calculated kW exceeds kVA, the units or formula are wrong.

Reverse calculation for feeder current

Suppose the design electrical input is 120 kW at 415 V and PF 0.90. I = 120,000 /(1.732 × 415 × 0.90) ≈ 185 A. This is load current, not a final cable or breaker rating. Apply duty, harmonics, ambient temperature, grouping, voltage drop, starting conditions and the applicable installation rules.

Motor example with efficiency

A motor delivers 75 kW mechanically at η = 0.94 and PF = 0.88 on 400 V. Electrical input is 75/0.94 = 79.8 kW. Current is 79,800 /(1.732 × 400 × 0.88) ≈ 131 A. Using 75 kW directly would understate current.

Unbalanced and distorted systems

For significant phase imbalance, calculate complex power per phase and sum it. For nonlinear loads, displacement power factor alone may not equal total power factor because harmonics increase RMS current. Use a suitable power-quality instrument and state the measurement method.

Common mistakes

  • Using 230 V in a 400 V line-to-line formula.
  • Applying motor efficiency twice—or not at all when starting from shaft output.
  • Treating demand factor as power factor.
  • Rounding √3 or intermediate results too early.
  • Using nominal PF instead of the value at expected loading.
  • Sizing protection directly from a simplified current calculation.

Verification checklist

  1. Mark every voltage as LL or LN.
  2. Write the unit beside each input.
  3. State whether kW is electrical input or useful output.
  4. Confirm PF and efficiency apply at the same operating point.
  5. Compare with nameplate or measured data.
  6. Run a phase-by-phase check when imbalance matters.

FAQ

Why is √3 used?

It follows from the 120° phase displacement and the relationship between line and phase quantities in a balanced system.

Can kVA be converted to kW without power factor?

No. kW = kVA × PF for the same operating point.

Does this calculate voltage drop?

No. Voltage drop also needs conductor impedance, length, arrangement and load angle.

Related guides

References

Educational example only. Final circuit design requires the applicable code, manufacturer data and qualified engineering review.

Related Articles